LAB ACCREDITATIONS AND CERTIFICATES

CALIBRATION | ONSITE CALIBRATION | ELECTRICAL SAFETY TESTING LABS

JM Test Systems is fully equipped to perform calibrations/certifications with standards traceable to the International System of Units (SI) through National Metrology Institutes (such as NIST, NRC, NPL, PTB, etc.), to consensus standards, to ratio methods, or to accepted values of natural physical constants. JM TEST SYSTEMS’ quality control system meets the requirements of ANSI/NCSL Z540-1, ISO 9001, and ISO 17025. For Electrical Testing Services including Grounding cables, Jumpers, Hot Sticks (Single, Cluster, Telescoping, Shotgun, Straight, and Static Discharge), Arc Flash Suits, Insulated tools and rubber goods such as: Gloves, Sleeves, Blankets, Coverups, Footwear, Matting, and Roll Blankets we are NAIL for PET accredited and follow the guidelines set in place by OSHA 29 CFR 1910 and 1926, NFPA NEC 2008 and various ASTM/ANSI standards.

A2LA and NAIL accredited JM Test Systems
Accredited Calibration Testing Lab

Our Quality Policy

JM Test Systems, Inc. will return to the customer equipment that is repaired, calibrated, certified and tested along with reliable and accurate test data. 100% of all equipment is thoroughly cleaned.

If necessary, the equipment will be restored to a “like new” appearance.

All equipment is 100% Quality assurance checked.

We will continually strive to improve the quality of our services through quality objectives, personnel training, internal and external auditing including technical oversight by highly skilled laboratory management.

We maintain accreditation to ISO 17025 requirements or conformance to ASTM standards, industry affiliations including professional organizations memberships along with the use and development of state-of-the-art measurement equipment and testing techniques.

Accreditation Resources

OTHER REPORTING AGENCIES JM TEST SYSTEMS IS IN COMPLIANCE WITH:

Calibration & Testing Service Options

JM Test Systems provides the highest quality calibration & testing.

Accuracy shown on all datasheets, with certificates listing all standards used during calibration and knowledge of before and after calibration data stated “in” or “out” of tolerance. Unless otherwise stated by customer requirements, only the UUT (Unit Under Test) specifications are considered when stating a condition of “in” or “out” of tolerance, and the calibration interval is set to 12 months. All “dielectrically tested” equipment is tested in accordance with ANSI and ASTM procedures. Unless previously instructed, calibration/testing intervals are set to 12 months. Gloves have an interval set to 6 months.

STANDARD CALIBRATION SERVICES INCLUDE:

  • Pick-up and delivery services-If applicable
  • Traceable Certificate of Calibration
  • Archiving of historical data for an indefinite period
  • Calibration Sticker
  • Calibration Seals where applicable
  • As-found and as left data
  • Retest Notice when calibration is due
  • General cleaning of the instrument
  • Online certification and status check

Calibration

With Before/After Data

  • ISO 10012 Compliant
  • ANSI/NCSL Z540-1 Compliant
  • Calibrated to published manufacturer specifications
  • Calibrated by JM standards
  • Full calibration report including: Equipment Condition, Lab Environment, Certificate number, Actions taken, JM procedure, and Quality Assurance Signature.

17025:2017 Accredited Calibration

with Before/After Data & Uncertainties

  • ISO 10012 Compliant
  • ANSI/NCSL Z540-1 Compliant
  • Calibrated to published manufacturer specifications
  • Calibrated by JM standards
  • Full calibration report including: Equipment Condition, Lab Environment, Certificate number, Actions taken, JM procedure, and Quality Assurance Signature.

PPE Testing

  • NAIL for PET accredited
  • Complies with OSHA 29 CFR 1910 and 1926
  • Complies with NFPA NEC 2008
  • Complies with ASTM/ANSI D120,F496,D1051,F496, D1048,F479,D1050,F478,D1049,F478,D178,D711,D712, ANSI-A92.2 ASTM F855-03, ASTM F1505
  • Includes Test Report with customer information, Report Number, Failure Rates, Test Voltages, Used Standards, and detailed equipment list.

Your Complete Solution

Calibration & Testing Service Types

In House Calibration

JM Test Systems provides calibration services for many industries. Our many accredited labs located around the USA will provide top quality service within our promised turnaround time.

View More

On-Site Calibration

For customers with large batches of equipment, or equipment that cannot leave the jobsite, JM Test provides qualified technicians for test equipment to be calibrated/tested at your facility. Our mobile onsite laboratories are managed through our fixed facilities. These services are covered by our ISO/IEC 17025 accreditation as an extension of these fixed facilities.

View More

Outsourced Calibration

JM Test Systems has a dedicated administrative team to locate a quality vendor to perform calibration outside of our scope. This team takes care of the shipping, RMA forms, and approvals so you don’t have to.

Repair Services

Equipment fails to operate, and that’s not a problem for JM Test. When parts are available, we will provide you with a repair estimate and detailed report of the issues your units have. Once we have received confirmation, we will proceed with repairs. Our commitment is to return your equipment in a like-new condition.

ESL Testing

Electrical Safety Equipment is tested in one of our many facilities across the USA. All equipment is cleaned and tested within our NAIL for PET accredited facilities.

View More

Pick up & Delivery

JM Test Systems provides pick up and delivery services near each of our locations to provide the safest handling for your equipment. Our friendly delivery drivers ensure expedite transportation. Ask if this service is available near you!

View More

Rental Equipment

Not only does JM Test Systems offer the largest inventories for test equipment, our equipment is tested EACH time it returns to our facility. This guarantees the equipment your using on your job has the most up-to-date calibration and certifications and also ensures you with top quality equipment.

View More

JM Test Systems
Customer Portal

A simpler way to manage your equipment.

24/7 Access
Print Test Report
Check Retest Dates
View Equipment Status

View More

Featured Articles

Digital Hydrostatic Testing

Digital Hydrostatic Testing WHAT IS HYDROSTATIC TESTING? Traditionally speaking, a hydrostatic test, also known as a “hydro test” or “pressure integrity test” is a leak test performed to test the integrity of a pipe, storage tank, pressure vessel, control components or connections (welded, fused or mechanical) of a vessel that will facilitate or store pressure … Continue reading “Digital Hydrostatic Testing”

Hydraulic and Pneumatic Torque Calibration

JM Test Systems is now able to repair and calibrate Hydraulic and Pneumatic/Electric torque wrenches in house thanks to our recently acquired AKO Torque Calibration System.    This industry-leading standard uses AKO’s TorqCal PRO Software, a hydraulic pump with precision regulator, pressure transducer measuring input pressure, and torque transducer measuring output torque for accurate, consistent calibrations … Continue reading “Hydraulic and Pneumatic Torque Calibration”

JM Test: Authorized Service Center for Georg Fischer

JM Test Systems is now an authorized service center for Georg Fischer MSA Electrofusion Processors. Georg Fischer piping systems, popular in gas and water distribution plants and systems, utilize high quality polyethylene systems with a revolutionary jointing system which virtually eliminates leakage for the lifetime of the system.  These electrofusion processors use current at a … Continue reading “JM Test: Authorized Service Center for Georg Fischer”

Valve Leakage Rates & Safety – JM Test Manufacturing

In April of 2022, the Pipeline and Hazardous Materials Safety Administration (PHMSA), a branch of the U.S. Department of Transportation, announced a new rule to help improve pipeline safety, reduce super-polluting methane emissions, and protect the public by requiring the installation of remotely controlled or automatic shut-off valves on new and replaced onshore natural gas, … Continue reading “Valve Leakage Rates & Safety – JM Test Manufacturing”